PolarsStar Jack V2
SPECIAL ORDER ITEM. WE DO NOT STOCK THIS ITEM AT OUR WALK IN STORE.
JACK™ V2 - M4/M16 Conversion Kit
Fire mode/s: Full Auto, Semi Auto, Variable Burst
Gearbox Profile: TM Spec Version 2
Included Nozzle Type: M4/M16 Series
Cyclic Rate: 1 RPS to 30+ RPS
Fire Modes: Semi / 2 to 9 Shot Burst, Semi / Full Auto, Semi Only
Power Source: HPA (High Pressure Air via remote air rig)
FCU Battery: 7-10VDC w/ JST Connector
PSI Operating Range: 40 psi. to 130 psi.
Build Material: Aluminum / Delrin
The JACK™ system was designed to answer the demand for an affordable, high performance HPA (High Pressure Air) conversion for AEG's. The system is a drop-in cylinder replacement that is universally compatible with a wide range of gearbox versions that have center-line nozzles.
Similar to its sister product, the F1, it replaces the original gearbox components with a programmable pneumatic system allowing for higher performance and greater reliability over a gear driven system. Although economically priced, JACK™ still retains the same performance and quality you have come to expect from PolarStar products.
JACK™ has only 1 moving part, the nozzle, which acts as its own poppet valve which is piloted by the solenoid. With the exception of the poppet being integral to the nozzle, the valve is similar to the poppet valve used in the previously released Fusion Engine™ and is what gives JACK™ its signature muzzle report. The system itself only has 6 parts and can be completely disassembled by hand in a matter of seconds so the system is very reliable and easy to maintain.
Just like all other PolarStar HPA conversions, JACK™ also allows for easy velocity adjustment. Using a standard M4 as an example, velocity can be adjusted from below 280fps and up to approximately 500fps with a .20g BB. This can be done simply by adjusting input pressure and poppet dwell to fine tune your rifles velocity in increments of just a few FPS at a time. Maximum velocity potential of the system will vary depending upon the barrels length and tightness of the bore. Longer and tighter barrels will yield a higher velocity while shorter or wider barrels will be yield a lower velocity.
As with all of PolarStar's electro-pneumatic conversion kits, you can quickly change and adjust key functions of JACK™ via the on-board FCU (Fire Control Unit) which is no bigger than an AEG's MOSFET and can easily fit inside of a rifles battery compartment along with a small Li-po battery. Using the FCU's five position joystick and LCD display you will be able to easily and precisely adjust such functions as the systems cyclic rate, fire modes and poppet dwell on the fly.
Although efficiency was not a critical requirement during development, JACK™ does boast some highly respectable figures in this category. This is made possible by its compact and intelligently laid out design which minimizes dead volume resulting in better air flow, faster response and less air used per shot. As a result JACK™ is considerably more air efficient than a bone stock Fusion Engine™ when operating in the same velocity range.
Designed, manufactured and built in the U.S.A..
Assembled from CNC machined aluminum components with high performance delrin nozzle.
Universal cylinder design is compatible with numerous gearbox versions.*
Optimized flow profile, firing point and flow path promotes superior shot consistency and accuracy.
Capable of functioning in damp and sub-freezing climates without affecting performance or reliability.
User selectable Semi/Full Auto, Semi Auto Only and Variable Burst modes.
Independently adjustable velocity and cyclic rate.
Auto Switch mode allows for proper selector configuration for specific models.
Easy to use Fire Control Unit (FCU) with LCD display and five position joystick.
Instantaneous trigger response. Faster than an AEG with a Li-po!
Required for operation: Complete TM Spec AEG rifle with gearbox, Regulated Air Rig, HPA Tank, Battery.
Installation: JACK™ will be installed into the shell of your AEG's gearbox. The only parts which you need to retain from your gearbox is the trigger w/ spring, safety assembly and selector components. Retain the original spring guide for models which require that the stock be secured to the gearbox and not the receiver.
*Compatibility: The Version 2 - M4/M16 kit is compatible with most TM Spec AEG's in that rifle series. This kit is compatible with other TM Spec rifles which use a Version 2 gearbox with the traditional open contact trigger switch. In most cases only a model specific nozzle is required to install the system into another model (i.e. M4 to MP5). If your rifle has an electronic micro switch (i.e. Ares Amoeba) you will need to purchase the kit for that specific model series which will include a different switchboard.
Power source: Only HPA or Nitrogen should be used with the JACK™ system. CO2 and Propane cannot be used. Using liquid propellants such as this can result in damage to the system.
KENTUCKY RESIDENTS. You must be 18 years of age or older to purchase any Airsoft Replica from BG Airsoft. An over 18 age waiver is required for all Replica Purchases. You DO NOT need a waiver for parts and accessories. Before your order is shipped you must download, sign, scan and email a signed Waiver to firstname.lastname@example.org Waivers can be downloaded by clicking on the BG Airsoft Waiver Link at the bottom of the menu on the left of this page.
While the sport of Airsoft is designed to be enjoyed by all ages, ignoring proper safety practices can turn a day of fun into a tragedy. Todays modern airsoft guns are capable of firing a BB at velocities that can and will penetrate fabric and skin, causing serious injury. Always wear "Full Seal" eye protection and observe proper weapon handling practices such as keeping the weapon on "safe" and cleared with the magazine out to prevent accidental discharge. REMEMBER!! Safety begins with the shooter!!